TRITOSIL FIREPROOF
High-quality one-component polyurethane fireproof foam. It has excellent thermal and sound insulation properties and excellent bonding strength. Homogeneous structure of the product provides excellent adhesion to the work surface.
Compliance with fire safety.
High thermal stability.
LOW-EXPANSION.
SCOPE:
Perfect for designs with a high fire resistance class. Used for mounting doors and windows fixing wall panels, roof tiles, insulation fixing tube filling holes and gaps as well as thermal insulation. Good adhesion to many construction materials, except Teflon, polyethylene and silicone surfaces.
APPLICATION
Before use, the foam cylinder temperature should be about 20°C. Heating cylinder is permitted in a container of warm water (up to +30°C). Vigorously shake the bottle for 30 seconds. Place the cylinder valve is facing up. Screw mounting part of the gun on to threaded portion of the adapter. Make sure the connection is secure. Place the can upside down. Start using the product. If necessary, repeat shaking.
IMPORTANT:
Before using the foam need to clean work surfaces from dust, ice, grease, and other contaminants, and moisten with water. Fresh dirt foam as well as the cured foam can be removed with acetone or TRITOSIL® Cleaner, or by mechanical ways. Cured foam can be painted.
INGREDIENTS: diphenylmethane diisocyanate (isomers and homologues) (CAS 9016-87-9), propane / butane / izobugan (CAS 74-98-6 (CAS: 106-97-8) / CAS 75-28-5). R20 Harmful by inhalation. RZ6 / 37/38 Irritating eyes, respiratory system and skin. R40 Limited confirmed carcinogenic effect. R42 / 43 Inhalation and skin contact can lead to allergies. R48 / 20 Harmful: Prolonged exposure through inhalation and ingestion of the risk of serious injury. S23 Do not breathe vapors. S36 / 37/39 Use personal protective equipment. Protect your face and eyes. S45 In case of accident or if you feel unwell, seek medical advice immediately and show this container or label. 851 Use only in well-ventilated areas. S63 In case of accidental inhalation, breathe in fresh air and keep quiet. Contains isocyanates. See information supplied by the manufacturer. Container is under pressure. Keep it away from direct sunlight, heat above 50°C. Do not pierce or burn even after use. Do not spray on a naked flame or any hot surfaces. Keep out of the reach of children. Keep away from sources of fire or smoke. Individuals who are sensitive to isocyanate may have allergic reactions when using this product. People suffering from asthma, eczema or having skin problems should avoid contact with this product. This product should not be used under conditions of poor ventilation without a mask with an attached gas filter (ie type A1 according to standard EN 14387).
SPECIFICATIONS
Fire resistance: up to 240 minutes.
Application temperature: +5°C to +30°C
Can temperature when using: + 10°C to + 25°C
Surface drying time: 10-16 minutes. Cured foam can be painted and machined 30-40 minutes after completion of the work at the ambient temperature of + 23 ° C and 50% relative humidity. After complete curing (24 hours) the foam must be protected from exposure to ultraviolet rays. Operating temperature: -50 ° C to + 90 ° C (for short periods of -65 ° C to + 130 ° C).
STORAGE
Stored and transported in an upright position. Store in a dry and ventilated place at temperatures between + °C to +30°C. Permitted to store or transport cylinders at -25 ° C for 25 days. Do not store near sources of heat, exposed to direct sunlight and mechanical stress, which can lead to damage and depressurization cylinders. Shelf life 12 months.
SAFETY:
R20 Harmful by inhalation. R36 / 37/38 Irritating eyes, respiratory system and skin. R41 there is a risk of serious damage to eyes. R42 / 43 Inhalation and skin contact can lead to allergies. S16 Keep away from sources of ignition and do not smoke. S23 Do not breathe vapors. S26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. S36 / 37/39 Use personal protective equipment. S46 If swallowed, seek medical advice and show the bottle and label. S51 Use only in well-ventilated areas S63 In case of inhalation, need to breathe in fresh air. Contains isocyanates, see information supplied by the manufacturer. Cylinder is pressurized; storage temperature should not exceed 50°C. Do not pierce or burn even after use. Keep out of the reach of children. Dispose of in accordance with local regulations.
TRITOSIL PU MEGA
APPLICATION:
PU Foam is designed for installation of windows and doors, filling gaps, thermal and acoustic insulation, and sealing compounds in the frame construction, as well as other construction and installation works.
Capacity: 65 liters
Volume increment (secondary expansion): 70-100%
Processing time: 40 minutes
Application temperature: -5°C to + 30°C
Can temperature: + 15°C to + 30°C
Water absorption (after 24 hours): 2.5%
High thermal and acoustic insulation level
Resistance to moisture and mildew
Shelf life: 12 months
All parameters are measured in accordance with international standards and are highly dependent on external conditions (can temperature, air and surface quality of the equipment used, the air pressure, qualification of users).
DIRECTIONS FOR USE:
Always use mechanical fasteners when installing windows and doors. Clean, degrease and moisten the surface with water. Shake can well and attach to a gun adapter. Hold the can upside down during use. Fill the gaps and joints up to 60% of depth (foam increases in volume). When the foam is fully cured it can be protected from UV by using a sealant, plaster or paint over it (not earlier than 24 hours after application). Fresh dirty foam as well as the cured foam can be removed with acetone or TRITOSIL® Cleaner, or by mechanical way. Cured foam can be painted.
INGREDIENTS: 4,4 – diphenyl methane diisocyanate (EC ? 202-966-0); propane (EC ? 200-827-9V), butane (EC ? 203-448-7V), isobutane (EC ? 200-857-2).
SAFETY: R20 Harmful by inhalation. R36 / 37/38 Irritating eyes, respiratory system and skin. R41 there is a risk of serious damage to eyes. R42 / 43 Inhalation and skin contact can lead to allergies. S16 Keep away from sources of ignition and do not smoke. S23 Do not breathe vapors. S26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. S36 / 37/39 Use personal protective equipment. S46 If swallowed, seek medical advice and show the bottle and label. S51 Use only in well-ventilated areas S63 In case of inhalation, need to breathe in fresh air. Contains isocyanates, see information supplied by the manufacturer. Cylinder is pressurized; storage temperature should not exceed 50°C. Do not pierce or burn even after use. Keep out of the reach of children. Dispose of in accordance with local regulations.
PU Foam Ultra
APPLICATION:
Professional foam designed for installation of windows and doors, filling gaps, thermal and acoustic insulation, and sealing compounds in the frame construction, as well as other construction and installation works.
Capacity: 45 liters
Volume increment (secondary expansion): 70-100%
Processing time: 40 minutes
Application temperature: -10°C to + 30°C
Can temperature of 15°C to + 30°C
Water absorption (after 24 hours): 2.5%
High level of thermal and acoustic insulation
Resistance to moisture and mildew
Shelf life: 12 months
All parameters are measured in accordance with international standards and are highly dependent on external conditions (can temperature, air and surface quality of the equipment used, the air pressure, the qualification of users).
DIRECTIONS FOR USE:
Always use mechanical fasteners when installing windows and doors. Clean, degrease and moisten the surface with water. Shake can well and attach to a gun adapter. Hold the can upside down during use. Fill the gaps and joints up to 60% of depth (foam increases in volume). When the foam is fully cured it can be protected from UV by using a sealant, plaster or paint over it (not earlier than 24 hours after application). Fresh dirty foam as well as the cured foam can be removed with acetone or TRITOSIL® Cleaner, or by mechanical way. Cured foam can be painted.
INGREDIENTS: 4,4 – diphenyl methane diisocyanate (EC ? 202-966-0); propane (EC ? 200-827-9V), butane (EC ? 203-448-7V), isobutane (EC ? 200-857-2).
SAFETY: R20 Harmful by inhalation. R36 / 37/38 Irritating eyes, respiratory system and skin. R41 there is a risk of serious damage to eyes. R42 / 43 Inhalation and skin contact can lead to allergies. S16 Keep away from sources of ignition and do not smoke. S23 Do not breathe vapors. S26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. S36 / 37/39 Use personal protective equipment. S46 If swallowed, seek medical advice and show the bottle and label. S51 Use only in well-ventilated areas S63 In case of inhalation, need to breathe in fresh air. Contains isocyanates, see information supplied by the manufacturer. Cylinder is pressurized; storage temperature should not exceed 50°C. Do not pierce or burn even after use. Keep out of the reach of children. Dispose of in accordance with local regulations.
Epoxy 5min
Product description
Crystal clear, fast, two-part epoxy adhesive.
Field of application
Ideal for fast, strong and invisible repairing of pottery, porcelain, glass, leather, wood, stone, metal and ceramics to themselves or to each other. Ideal for filling cracks thanks to filling capacity. Not suitable for Polyethylene (PE), polypropylene (PP), P.T.F.E. and silicone rubber.
Properties
- Fast
- Crystal clear
- Super strong
- Universal
- Suitable for numerous materials
- Temperature resistant from -40°C to +100°C
- Gap-filling
- Waterproof
- Chemicals resistant
- Paintable
Preparation
Working conditions: Only use at temperatures between +5°C and +35°C. Product cures after mixing resin and hardener.
Personal safety: Preferably wear gloves during use.
Surface requirements: Materials to be bonded should be dry, clean and free of grease.
Preliminary surface treatment:Degrease parts to be bonded with Bison Thinner for Bison Kit or acetone. Roughen up smooth materials (sand paper).
Tools: Mix and apply with plastic spatula. Clean tools with warm water and soap directly after use.
Application
Mixture ratio: 1:1
Coverage: 24 ml = approx. 240cm² (coat of 1mm)
Directions for use:
Remove spatula from side of double syringe and cap from handle. Break safety seal of double syringe. Dispense equal quantities of both parts into enclosed mixing tray. Stir well using enclosed spatula. At room temperature (+20°C), mixture remains workable for approx. 5 minutes. Apply a thin layer to one side. Join immediately and hold in place for 20 minutes. Do not move bonded parts until after complete cure. After use, clean nozzles with a cloth and place special double cap from handle on double syringe. Do not mix resin and hardener unless for bonding.
Potlife: 5 minutes
Stains/residue: Remove fresh stains immediately with warm water and soap. Cured adhesive residue can only be removed mechanically.
Cure times
Handling time: approx. 20 minutes
Dry/Cure time: approx. 1hour. Curing takes longer at lower temperatures, and shorter at higher temperatures.
Technical properties
Moisture resistance: Good
Water resistance: Good
Temperature resistance: -40°C to +100°C
Chemicals resistance: Good
Filling capacity: Good
Technical specifications
Chemical base: Resin: epoxy resin. Hardener: modified amide
Colour: Transparent
Viscosity: Liquid
Solid contents: approx. 100 %
Density: approx. 1.16 g/cm³
Storage conditions
At least 24 months after date of manufacture. Limited shelf life after opening. Store in a dry, cool and frost-free place.
Plastic Adhesive
High quality, strong glue for plastics.
Product description
High quality and strong glue for repairing many plastic(household) objects.
Field of application
Glues household synthetics such as ABS, acrylic glass polycarbonate and rigid PVC. Excellent for repairing plastic household appliances such as: (mobile) phone, coffee-maker, audio appliances, water boilers, remote control, computer, printer, keyboard. Also excellent for fixing pvc electrical tubes and plastic bicycle and car light parts. Not suitable for Polyethylene (PE), Polypropylene (PP) and P.T.F.E.
Properties
- Strong
- Waterproof
- Temperature resistant up to + 100°C
- Transparent
- Preparation
Preparation
Working conditions: Do not use at temperatures below +5°C.
Surface requirements: Materials to be glued should be clean, dry, and free of dust and grease.
Preliminary surface treatment: If necessary degrease with acetone.
Application
Directions for use:
Apply glue thinly to one side. Join immediately and press firmly on entire surface.
Stains/residue: Remove fresh stains immediately with acetone. Dried glue residue can only be removed mechanically.
Cure times
Handling time: approx. 3 hours.
Dry/Cure time: approx. 24 hours.
Dry/Cure time: approx. 24 hours.
Technical properties
Temperature resistance: Up to +100°C.
Chemicals resistance: Resistant to household cleaning products.
Technical specifications
Chemical base: PVC copolymer
Color: Transparent
Viscosity: Runny
Solid contents: approx. 25 %
Storage conditions
At least 24 months after date of manufacture. Limited shelf life after opening. Store in a dry, cool and frost-free place.
Epoxy Metal
Metal colored, hard wearing, two-part epoxy adhesive
Product description
Metal coloured, hardwearing, two-part epoxy adhesive.
Field ofapplication
Ideal for hardwearing repairs to metal objects which need to resist extreme conditions (forces, vibrations, (sea) water, heavy strains), such as tools or parts of a car, motorcycle, bicyle or moped, metal (garden) fences or cutlery. Also suitable for filling small holes in radiators. Bonds metal (steel, aluminium, iron) parts amongst themselves or to stone, wood, concrete and various synthetics (such as Formica, polyester and bakelite). Not suitable for Polyethylene (PE), Polypropylene (PP), P.T.F.E. and silicone rubber.
Properties
- Hardwearing
- Metal coloured
- Resistant to extreme conditions
- Temperature resistant from -40°C to +60°C
- Filling
- (Sea)water resistant
- High resistance to chemicals
- Can be sanded, filed, drilled and painted after curing
Preparation
Working conditions: Use only at temperatures between +5°C and +35°C. Product cures after mixing resin and hardener.
Personal safety: Preferably wear gloves during use.
Surface requirements: Materials to be bonded should be dry, clean and free of grease.
Preliminary surface treatment:Degrease parts to be bonded with Bison Thinner for Bison Kit or acetone. Roughen up smooth materials (sand paper).
Tools: Mix and apply with plastic spatula. Clean tools with warm water and soap directly after use.
Application
Mixture ratio: 1:1
Coverage: 24 ml = approx. 240cm² (coat of 1mm)
Directions for use:
Remove spatula from side of double syringe and cap from handle. Break safety seal of double syringe. Dispense equal quantities of both parts into enclosed mixing tray. Stir well using enclosed spatula until mixture has a uniform colour. At room temperature (+20°C), mixture remains workable for approx. 45 minutes. Apply a thin layer to one surface. Join immediately and hold in place for 10 hours. Do not move bonded parts until after complete cure. After use, clean nozzles with a cloth and place special double cap from handle on double syringe. Do not mix resin and hardener unless for bonding.
Potlife: 45 minutes
Stains/residue: Remove fresh stains immediately with warm water and soap. Cured adhesive residue can only be removed mechanically.
Cure times
Handling time: approx. 10 hours
Dry/Cure time: approx. 24 hours. Curing takes longer at lower temperatures, and shorter at higher temperatures.
Technical properties
Moisture resistance: Good
Temperature resistance: -40°C to +60°C
Chemicals resistance: Very Good
Paintability: Good
Filling capacity: Good
Technical specifications
Chemical base: Resin: epoxy resin. Hardener: modified amide
Colour: Grey
Viscosity: Pasty
Solid contents: approx. 100 %
Density: approx. 1.2 g/cm³
Storage conditions
At least 24 months after date of manufacture. Limited shelf life after opening. Store in a dry, cool and frost-free place.
Epoxy Universal
Universal, strong, two-part epoxy adhesive
Product description
Universal, strong, two-part epoxy adhesive.
Field ofapplication
Ideal for repairs to metals, pottery, porcelain, crystal, glass, ivory, pearls, precious stones and numerous synthetics (such as polyester, bakelite, Formica, rigid polystyrene and acrylic glass.Not suitable for Polyethylene (PE), Polypropylene (PP), P.T.F.E. and silicone rubber.
Properties
- Strong
- Temperature resistant from -20°C to +60°C
- Filling
- Water resistant
- Chemicals resistant
- Paintable
Preparation
Working conditions: Use only at temperatures between 5°C and +35°C. Product cures after mixing resin and hardener.
Personal safety: Preferably wear gloves during use.
Surface requirements: Materials to be bonded should be dry, clean and free of grease.
Preliminary surface treatment:Degrease parts to be bonded with Bison Thinner for Bison Kit or acetone. Roughen up smooth materials (sand paper).
Tools: Mix and apply with plastic spatula. Clean tools with warm water and soap directly after use.
Application
Mixture ratio: 1:1
Coverage: 24 ml = approx. 240cm² (coat of 1mm)
Directions for use:
Remove spatula from side of double syringe and cap from handle. Break safety seal of double syringe. Dispense equal quantities of both parts into enclosed mixing tray. Stir well using enclosed spatula until mixture has a uniform colour. At room temperature (+20°C), mixture remains workable for approx. 1,5 hours. Apply a thin layer to one surface. Join immediately and hold in place for 7 hours. Do not move bonded parts until after complete cure. After use, clean nozzles with a cloth and place special double cap from handle on double syringe. Do not mix resin and hardener unless for bonding.
Potlife: 1,5 hours.
Stains/residue: Remove fresh stains immediately with warm water and soap. Cured adhesive residue can only be removed mechanically.
Cure times
Handling time: approx. 7 hours.
Dry/Cure time: approx. 24 hours. Curing takes longer at lower temperatures, and shorter at higher temperatures
Technical Properties
Moisture resistance: Good
Temperature resistance: -20°C to + 60°C
Chemicals resistance: Good
Paintability: Good
Filling capacity: Good
Technical specifications
Chemical base: Resin: epoxy resin. Hardener: modified amide
Colour: Light yellow
Viscosity: Liquid
Solid contents: approx. 100 %
Density: approx. 1.15 g/cm³
Storage conditions
At least 24 months after date of manufacture. Limited shelf life after opening. Store in a dry, cool and frost-free place.
Super Glue Gel
Tear-off card with 12 tubes of universal super glue.
Product description
Super strong, fast, correctable and slightly filling super glue in the form of a gel. Ideal for porous materials.
Field of application
Glues various materials, such as earthenware, porcelain, cork, wood, cardboard, metal, rubber and many synthetics. Not suitable for Not suitable for some synthetics (PE, PP, PTFE and silicone rubber) and car windows.
Properties
- Does not drip or run down vertical surfaces
- Briefly correctable
- Slightly filling (also suitable for less well-fitting parts)
- Ideal for porous materials
- Super strong
- Fast
Preparation
Working conditions: Do not use at temperatures below +10°C.
Surface requirements: Materials to be fastened should be clean, dry, free of dust and grease and well-fitting.
Preliminary surface treatment:Degrease with acetone or Bison Thinner. Pretreat acid reacting surfaces (such as aluminium) with diluted ammonia, then rinse with water and wipe dry. Slightly roughen metals.
Tools: Work directly from the tube, using the very fine dispenser nozzle.
Application
Coverage: One drop covers approx. 2 cm² of surface to be glued. Only for spot bonding.
Directions for use:
Activate tube by turning cap. Do not push in tube while piercing. Do not open with scissors or knife. Apply glue as thinly as possible (less than one drop) on one side (too much glue slows down curing process significantly!). Nozzle should touch surface while applying glue. Immediately join parts and and press for a short time (10-60 seconds) to allow glue to spread evenly over surfaces. Manual pressure will do. When glueing metal, curing time can be shortened by, before joining, briefly breathing on side where glue is applied. After use, clean nozzle with a dry cloth and close tube by screwing black cap back on. Expose glue to air as little as possible.
Stains/residue: Wipe off excess glue immediately with a dry cloth. After curing, glue residue is very difficult to remove. Acetone will dissolve glue (but very slowly).
Points of attention: Attention: Super glue contains cyanoacrylate. Dangerous: will stick together skin and eyelids within seconds. Keep out of reach of children. In case of contact with skin, do not try to remove glue by force. In such cases, glue will automatically be rejected by skin. Then wash skin with water. In case of contact with eyes, keep eyelids open, rinse immediately with water and seek medical attention. Separate glued fingers by soaking them well in water and rolling a pencil between them.
Cure times
Handling time: approx. 15 seconds to 2 minutes, depending on nature of materials to be bonded. After 2-10 minutes glue joint is strong enough to be handled.
Full bond strength: Full bond strength after approx. 24 hours.
Technical properties
Moisture resistance: Good
Temperature resistance: -40°C to +80°C
Chemicals resistance: Good
Filling capacity: Good
Technical specifications
Chemical base: Cyanoacrylate
Color: Transparent
Viscosity: Liquid
Solid contents: approx. 100 %
Density: approx. 1.06 g/cm³
Storage conditions
At least 24 months after date of manufacture. Limited shelf life after opening. Store in a dry, cool, frost-free place. Storage below +5°C (in refrigerator) ensures maximum shelf life.
Super Glue Professional
Professional super glue in handy dispenser bottle.
Product description
Super strong, very fast, professional super glue in handy dispenser bottle.
Field of application
Glues various materials, such as most synthetics, metal, rubber, porcelain, wood and cork. Not suitable for earthenware, several synthetics (PE, PP, PTFE and silicones) and car windows.
Properties
- Industrial quality.
- In handy dispenser bottle
- Super strong
- Very fast
- Clear
Preparation
Working conditions: Do not use at temperatures below +10°C.
Surface requirements: Materials to be fastened should be clean, dry, free of dust and grease and well-fitting.
Preliminary surface treatment:Degrease with acetone or Bison Thinner. Pretreat acid reacting surfaces (such as aluminium) with diluted ammonia, then rinse with water and wipe dry. Slightly roughen metals.
Tools: Work directly from the bottle, using the very fine dispenser nozzle.
Application
Coverage: One drop covers approx. 2 cm² of surface to be glued. Only for spot bonding.
Directions for use:
Open bottle by pressing and turning cap at the same time. Apply glue as thinly as possible on one side (too much glue slows down curing process significantly!). Immediately join parts and press for a short time (10-60 seconds) to allow glue to spread evenly over surfaces. Manual pressure will do. The connection can be reinforced by dripping some extra glue into the joint. When glueing metal, curing time can be shortened by, before joining, briefly breathing on side where glue is applied. Clean nozzle with dry cloth immediately after use. Then close bottle by replacing cap. Expose glue to air as little as possible.
Stains/residue: Wipe off excess glue immediately with a dry cloth. After curing, glue residue is very difficult to remove. Acetone will dissolve glue (but very slowly).
Points of attention: Attention: Super glue contains cyanoacrylate. Dangerous: will stick together skin and eyelids within seconds. Keep out of reach of children. In case of contact with skin, do not try to remove glue by force. In such cases, glue will automatically be rejected by skin. Then wash skin with water. In case of contact with eyes, keep eyelids open, rinse immediately with water and seek medical attention. Separate glued fingers by soaking them well in water and rolling a pencil between them.
Cure times
Handling time: approx. 10 seconds to 1minute, depending on nature of materials to be bonded. After 2-5 minutes glue joint is strong enough to be handled.
Full bond strength: Full bond strength after approx. 24 hours
Technical properties
Moisture resistance: Good
Temperature resistance: -40°C to +80°C
Chemicals resistance: Good
Filling capacity: Limited
Technical specifications Chemical base: Cyanoacrylate
Color: Transparent
Viscosity: Runny
Solid contents: approx. 100 %
Density: approx. 1.06 g/cm³
Storage conditions
At least 18 months after date of manufacture. Limited shelf life after opening. Store in a dry, cool, frost-free place. Storage below +5°C (in refrigerator) ensures maximum shelf life.
Super Glue Liquid
Tear-off card with 12 tubes of universal super glue.
Product description
Super strong, very fast, universal super glue.
Field of application
Glues various materials, such as many synthetics, metal, rubber, porcelain, wood and cork. Not suitable for earthenware, several synthetics (PE, PP, PTFE and silicone rubber) and car windows.
Properties
- Super strong
- Very fast
Preparation
Working conditions: Do not use at temperatures below +10°C.
Surface requirements: Materials to be fastened should be clean, dry, free of dust and grease and well-fitting.
Preliminary surface treatment:Degrease with acetone or Bison Thinner. Pretreat acid reacting surfaces (such as aluminium) with diluted ammonia, then rinse with water and wipe dry. Slightly roughen metals.
Tools: Work directly from the tube, using the very fine dispenser nozzle.
Application
Coverage: One drop covers approx. 2 cm² of surface to be glued.
Directions for use:
Activate tube by turning cap. Do not push in tube while piercing. Do not open with scissors or knife. Screw white cap on opened tube. Apply glue as thinly as possible (less than one drop) on one side (too much glue slows down curing process significantly!). Nozzle should touch surface while applying glue. Immediately join parts and and press for a short time (10-60 seconds) to allow glue to spread evenly over surfaces. Manual pressure will do. The connection
can be reinforced by dripping some extra glue into the joint. When glueing metal, curing time can be shortened by, before joining, briefly breathing on side where glue is applied. After use, clean nozzle with a dry cloth and close tube by screwing black cap back on. Expose glue to air as little as possible.
Stains/residue: Wipe off excess glue immediately with a dry cloth. After curing, glue residue is very difficult to remove. Acetone will dissolve glue (but very slowly).
Points of attention: Attention:Super glue contains cyanoacrylate. Dangerous: will stick together skin and eyelids within seconds. Keep out of reach of children. In case of contact with skin, do not try to remove glue by force. In such cases, glue will automatically be rejected by skin. Then wash skin with water. In case of contact with eyes, keep eyelids open, rinse immediately with water and seek medical attention. Separate glued fingers by soaking them well in water and rolling a pencil between them.
Cure times
Handling time: approx. 10 seconds to 1minute, depending on nature of materials to be bonded. After 2-5 minutes glue joint is strong enough to be handled.
Full bond strength: Full bond strength after approx. 24 hours
Technical properties
Moisture resistance: Good
Temperature resistance: -40°C to +80°C
Chemicals resistance: Good
Filling capacity: Limited
Technical specifications
Chemical base: Cyanoacrylate
Color: Transparent
Viscosity: Runny
Solid contents: approx. 100 %
Density: approx. 1.08 g/cm³
Storage conditions
At least 24 months after date of manufacture. Limited shelf life after opening. Store in a dry, cool, frost-free place. Storage below +5°C (in refrigerator) ensures maximum shelf life.
-
-
Tweet
-